Product
Who We Are
1、Core function and application value
John Deere RE167207 oil pressure sensor, as a core component of John Deere engine lubrication system, ensures that the engine maintains optimal lubrication in high-load operation by monitoring the pressure of the main oil channel in real time. Its precise design can reduce the wear and tear of components caused by oil pressure fluctuations and extend the engine life by 15%-20%, which is especially suitable for 24-hour continuous operation scenarios of tractors, harvesters and other agricultural machinery and mining equipment.
2、Key Technical Advantages
Harsh Environment Resistance
The 316L stainless steel housing with IP67 protection level is designed to resist mud, water, dust and corrosive oil erosion. The internal potting of high-temperature silicone rubber maintains signal stability over a wide temperature range from -40℃ to 125℃, which meets the needs of long-term use in the high-temperature area of the engine compartment.
Intelligent Fault Diagnosis
Integrated self-diagnostic circuitry automatically triggers a fault code (e.g., P01CA) and outputs a safety signal when there is an abnormality such as a broken wire, short circuit, or over-range, helping users to quickly locate the problem and reduce downtime.
Accurate Measurement and Fast Response
sensor adopts piezoresistive measurement principle, with a response time of < 50ms and an accuracy of ±1.5% FS, which can promptly capture the subtle changes in oil pressure and provide reliable data support for equipment maintenance.
3. Applicable Scenarios and Applicable Models
RE167207 sensors are widely used in the following fields:
Agricultural Machinery: Compatible with John Deere 6R/7R series tractors and S700 series combine harvesters, which can support high-intensity operations such as deep plowing and planting in farmland;
Construction Machinery: Compatible with 300G series loaders and 850K series bulldozers, which can cope with the harsh working conditions of mines and infrastructures;
Electric Power: Compatible with PowerTech PSS series generator sets, which can provide reliable data support for the maintenance of equipment. PowerTech PSS series generator sets, to ensure the stable operation of the backup power system.
4. Installation and Maintenance Suggestions
Installation Specifications
Use special sockets and tighten them according to 27Nm torque to avoid deformation of the shell due to over-tightening;
Installation location should be far away from vibration sources, and the direct connection port of the main oil pipeline is preferred to minimize the pressure loss;
Make sure that waterproof seals of the wiring harness plugs are intact, to prevent water from entering into the water and causing a short-circuit.
Maintenance Intervals
It is recommended that calibration be performed every 500 hours or annually to verify the sensor zero point and full scale output through the John Deere Diagnostic Tool to ensure measurement accuracy. Daily maintenance should check the appearance of the sensor for corrosion or mechanical damage, and clean the impurities around the mounting holes in a timely manner.
5, quality assurance and purchase advice
John Deere strictly implement ISO 9001:2015 quality management system, each batch of products through the salt spray corrosion, dynamic pressure cycle and other tests to ensure long-term reliability. Users can confirm the suitable models through John Deere official parts inquiry system (John Deere Parts), and give priority to products with original anti-counterfeiting labels to avoid compatibility problems caused by non-genuine products.
Cost-benefit analysis
RE167207 sensor can achieve:
Efficiency improvement: accurate oil pressure monitoring to optimize the lubrication strategy, reduce engine fuel consumption by 3%-5%;
Maintenance cost reduction: long-life design (life ≥15,000 hours under normal working conditions) to reduce the frequency of replacement, combined with preventive maintenance, can reduce the annual maintenance costs by 30%;
Safety: through the global engineering team's working conditions simulation verification, avoiding the lubrication of the engine to avoid the lubrication of the engine. Safety guarantee: through the global engineering team's working condition simulation verification, avoiding the major equipment failure caused by lubrication failure.
Contact us at
If you need to get the list of suitable models, technical parameter table or bulk purchase quotation, please feel free to contact us by the following ways:
Ningbo Qiu Linn Trade Co., Ltd. service supply sales center
We provide more different brands of engine assemblies and spare parts
If you are interested in it, you can add my contact information directly: +86 15888032469
or email me: allen@perkins- rx.com Note the model or model number. rx.com
Note the model number or serial number for faster processing and favorable price
We provide global logistics and distribution services, original genuine products, support for online orders, to ensure that within 72 hours to respond to customer needs.
